SIM7000G NB-IoT / Cat-M / EDGE / GPRS HAT for Raspberry Pi, GNSS, Global Band Support

Neohodnotené

Značka: Waveshare

SKU: 20681

Dostupnosť	Zvyčajne do 3-7 dní
Môžeme doručiť do:	30.12.2024
Možnosti doručenia
Kód:	22698

42,99 € / ks 35,83 € bez DPH

SIM7000G NB-IoT / Cat-M / EDGE / GPRS HAT for Raspberry Pi, GNSS, Global Band Support

Neohodnotené

Značka: Waveshare

SIM7000G NB-IoT / Cat-M / EDGE / GPRS HAT for Raspberry Pi, GNSS, Global Band Support

14 dní

na vrátenie tovaru

Do 14:00 objednané

ešte dnes odoslané

Vernostné zľavy 5%

pre registrovaných zákazníkov

Popis
Diskusia

SIM7000G NB-IoT / Cat-M / EDGE / GPRS HAT for Raspberry Pi, GNSS, Global Band Support

SIM7000G NB-IoT / Cat-M / EDGE / GPRS HAT For Raspberry Pi, GNSS Positioning, Global Band Support

NB-IOT / CAT-M / GPRS / GNSS HAT

Low Power Narrow Band Cellular IoT Communication Module For Raspberry Pi

Based on SIM7000G

This is a telecommunication HAT for Raspberry Pi which supports global bands of NB-IoT, Cat-M, and GPRS, as well as GNSS positioning function. Due to its advantages like small size, low delay, and wide coverage, it is the ideal choice for IoT applications such as intelligent instruments, asset tracking, remote monitoring, e-health, and so on.

Features At A Glance

Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards
Supports TCP, UDP, PPP, HTTP, FTP, MQTT, SMS, Mail, etc.
Supports GNSS positioning (GPS, BeiDou, GLONASS)
Onboard USB interface, to test AT Commands, get GPS positioning data, and so on
Breakout UART control pins, to connect with host boards like Arduino/STM32
Onboard voltage translator, 3.3V by default, allows to be switched to 5V via 0Ω resistor
SIM card slot, compatible with both normal SIM card and NB-IoT specific card
2x LED indicators, easy to monitor the working status
Baudrate: 300bps~3686400bps (115200bps by default)
Control via AT commands (3GPP TS 27.007, 27.005, and SIMCOM enhanced AT Commands)
Supports SIM application toolkit: SAT Class 3, GSM 11.14 Release 98, USAT
Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)

Specifications

NB-IOT / CAT-M / 2G
Frequency bands	NB-IoT: B1, B2, B3, B4, B5, B8, B12, B13, B17, B18, B19, B20, B25, B26, B28
	Cat-M: B1, B2, B3, B4, B5, B8, B12, B13, B17, B18, B19, B20, B25, B26, B28, B39
	GPRS/EDGE: 850, 900, 1800, 1900MHz
Data rate	NB-IoT: 34(DL)/66(UL)
	Cat-M: 300(DL)/375(UL)
	EDGE: 236.8(DL)/236.8(UL)
	GPRS: 85.6(DL)/85.6(UL)
SIM card support	NB-IoT: NB Specific (Not Included)
SIM card support	Cat-M/GPRS/EDGE: Normal SIM (Not Included)
Applicable region	Global
GNSS
Satellite systems	GPS, BeiDou, GLONASS
Receiver type	16-channel
Receiver type	C/A Code
Sensitivity	Tracking: -162 dBm (GPS) / -157 dBm (GLONASS) / TBD (BD)
Sensitivity	Cold starts: -148 dBm
Time-To-First-Fix	Cold starts: <35s
Time-To-First-Fix	Hot starts: <1s
Accuracy	Position: <2.5m CEP
OTHER
Power supply	5V
Operating voltage	5V / 3.3V (3.3V by default)
Sleep Mode current	1.2mA (@DRX=2.56s)
Power Save Mode current	9uA
Operating temperature	-40°C ~ 85°C
Storage temperature	-45°C ~ 90°C
Dimensions	30.2mm x 65mm

Standard Raspberry Pi 40PIN GPIO

Compatible With Raspberry Pi Series Boards

Global Band Support Of NB-IoT/Cat-M/2G

Cloud Communication

Supports Communication Protocols Including
TCP, UDP, PPP, HTTP, FTP, MQTT, SMS, Mail...

GNSS Positioning

Supports GPS, BeiDou, GLONASS Positioning

What's On Board

SIM7000G
SPX29302 power chip
RT9193-33 power chip
Raspberry Pi GPIO header
for connecting with Raspberry Pi
USB interface
for testing AT Commands, getting GPS positioning data, etc.
SIM7000G control interface
for connecting with host boards like Arduino/STM32
SIM card slot
supports 1.8V/3V SIM card
GNSS antenna connector
LTE antenna connector

Network status indicator
Power indicator
Operating voltage selection jumper
configured via 0Ω resistor jumper
A: set operating voltage as 5V
B: set operating voltage as 3.3V (default)
DTR configuration jumper
configured via 0Ω resistor jumper
A: DTR is controlled by the Raspberry Pi P26 pin
B: NC (default)
PWR configuration jumper
configured via 0Ω resistor jumper
A: startup/shutdown by the Raspberry Pi P4 pin
B: auto startup on power-up (default)