Upozornenie!

Vitajte na našej novej stránke! Treba sa znova registrovať . 

Získajte tým 5% zľavu!

 

Viac
    Registrácia
    Domov / IoT - moduly / Vývojové dosky a klony / ARM , DSP , ESP , MCU , STM32 / STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32

    STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32

    Neohodnotené
    Značka: Waveshare

    STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32

    SKU: 22943

    Dostupnosť Skladom (1 ks)
    Môžeme doručiť do:
    27.11.2024
    Možnosti doručenia
    Kód: 20182
    29,90 € / ks 24,92 € bez DPH
    STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32
    Neohodnotené
    Značka: Waveshare
    STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32
    14 dní na vrátenie
    14 dní
    na vrátenie tovaru
    Objednávka do 14:00
    Do 14:00 objednané
    ešte dnes odoslané
    Vernostné zľavy 5%
    Vernostné zľavy 5%
    pre registrovaných zákazníkov

    STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32

    STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32
    STLINK-V3MINIE
    STM32 Debugger/Programmer

    Based On Arm Cortex-M STM32 32-Bit Microcontroller

     

    The STLINK-V3MINIE is a stand-alone debugging and programming tiny probe for STM32 microcontrollers, portable and easy-to-use. Onboard JTAG/SWD interfaces for communicating with STM32 microcontroller, also provides a virtual COM port for the host PC to communicate with the target microcontroller through one UART.

    Features At A Glance
    • Tiny 15 mm × 42 mm stand-alone debugging and programming probe for STM32 microcontrollers
    • Self-powered through a USB Type-C connector
    • USB 2.0 high-speed interface
    • Probe firmware is updatable through USB
    • Support drag-and-drop Flash programming of binary files
    • Two color LEDs: communication, power
    • JTAG communication support up to 21 MHz
    • SWD (Serial Wire Debug) and SWV (Serial Wire Viewer) communication support up to 24 MHz
    • Virtual COM port (VCP) up to 15 Mbps
    • 1.65 to 3.60 V application voltage support
    Interface Introduction

    Software Support
    Hardware Support

    Support All STM32 Series MCUs With JTAG / SWD Interfaces

    for reference only, STM32 MCU is not included.

    STLINK Series Selection Guide
    ITEMV3MINIEV3SETV2
    JTAG/SWD APPLICATION VOLTAGE1.65V~3.6V①3V~3.6V1.65V~3.6V①
    SWIM APPLICATION VOLTAGEN/A1.65V~5.5V1.65V~5.5V
    SWV SUPPORTYES②
    DEBUG INTERFACEmultimulti③2
    LED INDICATORtwo colors④
    ① ST-LINK/V2 and STLINK-V3MINIE support STM32 low-power devices.
    ② Only available for STM32 at present.
    ③ STLINK-V3SET features GPIO port besides the programming port.
    ④ Two colors LED indicates both power and communication.

    Connection Example

     

    What's On Board
    1. USB Type-C connector
    2. Power LED indicator pad (LED is not soldered here)
    3. STM32F723 MCU
    4. BTB (board-to-board) card edge connector pads
    5. STDC14 debug connector
     
    1. COM LED Indicator
      The LED is blinking red: the first USB enumeration with the PC is taking place.
      The LED is red: the communication between the PC and STLINK-V3MINIE is established.(end of enumeration).
      The LED is blinking green/red: data are being exchanged between the target and the PC.
    Outline Dimensions
    Resources & Services
    Wiki: www.waveshare.com/wiki/STLINK-V3MINIE
    PACKAGE CONTENT

    Weight: 0.058 kg

    Buďte prvý, kto napíše príspevok k tejto položke.

    Len registrovaní používatelia môžu pridávať príspevky. Prosím prihláste sa alebo sa zaregistrujte.

    Nevypĺňajte toto pole: